Skip to content

24/7 emergency repairs across Gauteng

081 566 5451

Gate motors · Sliding gates

Sliding gate repairs near me: the gate, its track and its motor

A sliding gate is only as good as the track it runs on. We repair the whole system, from seized wheels and bent tracks to the rack, the motor and its remotes, across Johannesburg, the East Rand and Centurion, and we install new sliding gate motors.

Our promise

Six-month guarantee on our repairs

Our promise

1-year guarantee on every motor kit we supply and install

Gloved hands fitting a steel gear rack along the bottom of a sliding gate, the motor's pinion gear beside it

How a sliding gate system works

The gate rolls along a ground track on its wheels, held upright by guide rollers at the top. A motor beside the gate turns a small gear, the pinion, which drives a toothed rack fixed along the gate. Limit magnets or a position counter tell the motor where open and closed are, and safety beams across the opening stop it closing on a car.

A trackless sliding gate, also called a cantilever gate, has no ground track at all: it hangs from roller carriages fixed beside the opening and rolls on those instead, which suits a driveway where a track would fill with stones, or ground too uneven for one. It's still driven by a pinion and rack, so the same sliding gate motors work it.

Every one of those parts can stop the gate, and a fault in one often shows up somewhere else: a seized wheel makes the motor strain until it trips its collision sensing, and a sagging rack wears out the pinion. That's why we look at the gate before the motor.

What a sliding gate needs to run well

ET's installation manual sets out what a gate should be like before a motor goes on it. It's a good checklist for an old gate too:

  • A straight leaf. The face the rack is fixed to should be true, without a bow along its length.
  • A secure, level track, straight and clear of stones and debris.
  • Good wheels. ET recommends steel wheels of at least 100 mm with sealed roller bearings: the bigger the wheel, the less effort it takes to roll.
  • Guide rollers at the top, nylon-clad on sealed bearings, never below halfway up the gate, and never touching both sides of their channel at once.
  • End stoppers at both ends of the track, so the gate can't run off it. ET calls this a national safety standard requirement, and Gemini says the stoppers in its kits must never be left off.

A gate in good order should take no more than about 30 kgf on a spring scale to start moving and 24 kgf to keep moving, for a motor like ET's Drive 300. Anything stiffer is a gate repair before it's a motor problem.

A technician aligning a safety beam on a short post beside a sliding gate

The rack and the pinion

The gap between the rack and the pinion matters more than most people think. ET's manual puts it at 1 to 2 mm between the teeth, and Gemini's at about 2 mm, so the rack never presses down on the motor.

  • Too tight, and the gate drags, worst in cold weather, and the motor may stop as if something were in the way.
  • Too loose, and the teeth skip under load, the motor loses track of where the gate is, and the teeth eventually strip.

Racks also drop over time as wheels wear and screws work loose. Resetting a rack, or replacing worn lengths and a worn pinion, is one of the most useful sliding gate repairs there is.

Which motor suits which sliding gate

Sliding gate motors are sized by the heaviest gate they're built for, and by how often they may run:

Sliding gate motors by gate weight, from the makers' manuals and spec sheets
Heaviest gateMotorsRead more
300 kgET Drive 300, Centurion D3 SMARTET Drive 300 manual
500 kgCenturion D5-Evo and D5 SMART, ET Drive 500 and 600, Gemini Slider 500ET Drive 500 manual, Centurion D5-Evo manual
600 kgCenturion D6 SMART, Gemini 24V Slider 600Centurion manuals
800 kgGemini 24V Slider 800Gemini manuals
1,000 kgCenturion D10, ET Drive 1000Centurion D10 manual

A gate that opens dozens of times an hour, at a complex or a business, needs a motor built for high traffic as well as the weight. Our installed kits for the usual driveway gate are below. Prices checked October 2026.

  • Sliding gate kit

    Centurion D5-Evo SMART sliding gate kit

    R7 999incl. installation

    In the kit

    • D5-Evo SMART motor (gates up to 500 kg)
    • 12 V 7 Ah battery
    • 2 × 4-button NOVA remotes
    • 4 m steel rack
    Our promise

    1-year guarantee on every motor kit we supply and install

  • Sliding gate kit

    ET Drive 500 sliding gate kit

    R6 999incl. installation

    In the kit

    • Drive 500 (gates up to 500 kg)
    • 12 V 7 Ah battery
    • 4 m steel rack
    • 2 × 4-button ET remotes
    Our promise

    1-year guarantee on every motor kit we supply and install

  • Sliding gate kit

    Gemini 12 V DC slider kit

    R6 999incl. installation

    In the kit

    • Gemini DC slider (gates up to 500 kg)
    • 2 × 3-button Gemini remotes
    • 12 V 7 Ah battery
    • 4 m steel rack
    Our promise

    1-year guarantee on every motor kit we supply and install

Prices checked October 2026. Price includes the kit listed, standard installation on a gate or door that already runs freely, and our 1-year kit guarantee. Not included: a power point at the motor if there isn't one (a job for a registered electrician), extra rack, gate or door repairs, and accessories. These are quoted before any work starts.

Compare two kits

SpecCenturion D5-Evo SMART sliding gate kitET Drive 500 sliding gate kit
Price, installedR7 999R6 999
ForSliding gateSliding gate
In the boxD5-Evo SMART motor (gates up to 500 kg)Drive 500 (gates up to 500 kg)
In the box12 V 7 Ah battery12 V 7 Ah battery
In the box2 × 4-button NOVA remotes4 m steel rack
In the box4 m steel rack2 × 4-button ET remotes
Guarantee1-year guarantee on every motor kit we supply and install1-year guarantee on every motor kit we supply and install

Common sliding gate faults

  • Hard to push by hand, even with the motor released: worn or seized wheels, stones in the track, a bent track or a guide roller that binds.
  • Stops and reverses on its own: usually the same, or a rack pressing on the pinion. Raising the motor's force setting only hides it. Choosing between a sliding and a swing gate in the first place is on sliding vs swing gates.
  • Opens or closes short: the limit magnet on the rack has moved, or the rack has slipped.
  • Clunks or jumps: rack teeth skipping on a loose rack, or a worn pinion.
  • Leans or rocks: a guide roller has worn, bent or come loose. Keep clear: a gate off its guides can fall.

All our spare parts are genuine, and every repair carries our six-month guarantee on our repairs. Same-day repairs are possible whenever the day's bookings allow.

A technician kneels beside a sliding gate motor with its cover off, checking the control board with a multimeter

Installing a motor on a sliding gate

Where the motor goes matters. ET's manual asks for the base plate to sit above the highest water that runs down the driveway, and for the motor to stand on the far side of the gate's guide post from the driveway, out of the path of cars. Cables go in before the motor, in conduit.

A motor that runs on mains needs a weatherproof isolator within 1.5 m of it, and the mains circuit itself is a job for a registered electrician. The whole job is on gate motor installation, and the price of each kit on gate motor prices. Your exact price is set in a free quote before any work starts. No call-out fee when we do the work. If no work is done, a R650 call-out fee applies.

Sliding gate repairs near you

We come to you in 21 areas across Johannesburg, the East Rand and Centurion.

Questions

Sliding gate questions

Why is my sliding gate so hard to push?

Almost always the wheels, the track or a guide roller: a seized bearing, stones or a bend in the track, or a roller binding at the top. Put the motor on manual first, then push the gate slowly and feel where it sticks. See what a gate needs to run well.

What size wheels should a sliding gate have?

ET's manual recommends steel or steel-alloy wheels of at least 100 mm with sealed roller bearings, because larger wheels roll more easily and hold their line. The wheel's groove should match the profile of the track. Read the full checklist.

Do you repair the gate as well as the motor?

Yes: wheels, guide rollers, tracks, racks, pinions and end stoppers, as well as the motor, its remotes and its beams. On a sliding gate the two are rarely separate problems. See common sliding gate faults.

Book a technician

Get a gate motor quote

Job card

We WhatsApp or call you back. Fields marked (required) are needed.

Property type
When
Photos (optional, up to 4)

No call-out fee when we do the work. If no work is done, a R650 call-out fee applies.