Skip to content

24/7 emergency repairs across Gauteng

081 566 5451

Gate motors · Saxonworld

Gate motor repairs in Saxonworld, for solid swing gates

A clad swing gate that stalls on a gusty afternoon, a bracket working loose from an old brick pillar, a release key nobody can find: we repair and fit gate motors across Saxonwold.

Our promise

Six-month guarantee on our repairs

Our promise

1-year guarantee on every motor kit we supply and install

Saxonworld

Saxonworld and the areas around it. Every area we cover

Swing gates that keep the street out

Saxonwold was laid out in 1925, and where a home opens onto the street through a pair of swing gates between pillars, the gates have often been clad solid over the years, with steel sheet or timber boards, for privacy. That keeps the street out, but it changes the job a motor has to do.

A swing motor has to deal with the leaf's weight, its length and the wind pushing on it. Centurion's installation manual for its V400 and V500 Vantage operators, made for anything from a light domestic gate to a heavy industrial pair, gives figures for all three, and they show why a motor that sails through a palisade gate can struggle with a solid one.

A technician adjusting the bracket of a gate arm on a brick pillar beside a double swing gate

Wind: the load nobody weighs

A solid gate leaf acts like a sail. Centurion's tables give the wind speed up to which the operator will still move a 1.8 m high gate, for a gate about a quarter covered (palisade and the like) and for one that's fully clad. Some examples:

Wind speed up to which a V400 or V500 still operates a 1.8 m gate
Leaf lengthInstalled A or B dimensionAbout a quarter coveredFully clad
Up to 1.5 m180 mm138 km/h69 km/h
Up to 2 m100 mm66 km/h33 km/h
Up to 2.5 m220 mm89 km/h44 km/h

Cladding roughly halves the wind a gate can be moved against. The geometry matters too: the A and B dimensions, which set where the brackets sit relative to the hinge, raise those speeds as they grow. So on a clad gate we give the motor all the leverage the site allows, and if it still can't cope with the gusts, we say so before fitting anything.

Weight, length and how far it opens

The heavier and longer the leaf, and the further it swings, the harder the motor works, as Centurion's limits for a 2.5 m leaf show:

Heaviest 2.5 m leaf by opening angle
Opening angleV400V500
90°500 kg750 kg
110°198 kg320 kg
120°65 kg110 kg

Past 2.5 m, Centurion doesn't recommend opening to 120° at all. To find your gate's angle, mark the ground 1 m from the centre of the hinge along the closed gate, and again along the open gate, then measure between the marks. Between 1,414 mm and 1,521 mm means an angle of 90° to 99°; between 1,532 mm and 1,638 mm, 100° to 110°.

Long leaves need a lock

The motor holds a swing leaf from near the hinge, so a long leaf can be forced at its far end. For any leaf longer than 3 m, Centurion's manual calls for an electric lock to hold the gate closed, and its weight and wind figures for the longest leaves are given with one fitted.

Old pillars and brackets

Every push and pull goes into the pillar through the wall bracket, so its fixing matters, especially on an old pillar:

  • Masonry pillars in frequent use: chemical anchors.
  • Precast walling or heavy, busy gates: bolts right through the wall.
  • Steel pillars: welded.
  • Lighter domestic gates: sleeve anchors or rawl bolts.

The gate bracket is welded, or held with high-tensile through-bolts on a light, little-used gate; Centurion doesn't recommend self-drilling screws or mild-steel bolts. For a gate opening 90° inward, the hinge can sit at most 165 mm (V400) or 245 mm (V500) back from the pillar's edge, or the gate may have to be moved on the pillar, and there must be more than 200 mm between the open gate and the side wall. Where there isn't, an outward-opening layout may work instead.

Is the gate ready for a motor?

Centurion lists what a gate must be before a motor goes on: it swings freely, stays put when left in any position, and each leaf is strong and rigid. Binding hinges or a dropped, scraping leaf are put right first, or the motor works harder and fails sooner. The motor goes on the inside, never where the public can reach it, and Centurion always recommends safety beams.

The release key: write its number down

In a power failure, a Vantage is released by key so the gate can be swung by hand. Each operator comes with its own set of keys, and Centurion's manual asks for the key number to be recorded. Do it now: a lost key with no number is a slow problem on the day you need it.

Gate motor repairs in Saxonwold

We repair swing and sliding gate motors from Centurion, ET, Gemini, Nice and Digidoor, and the gates they move: hinges, brackets, end stops, locks and beams. All our spare parts are genuine, and every repair comes with our six-month guarantee on our repairs. The fault finder below starts with the safe checks.

New kits for swing gates

Our swing kits are installed at a set price with battery back-up and remotes, and carry our 1-year guarantee on every motor kit we supply and install: the Centurion Vantage 500 double swing kit at R15 799, and the ET Wingo double swing kit at R13 999 for lighter gates. A very heavy or very long gate is quoted on site. Prices checked October 2026. Your exact price is set in a free quote before any work starts. No call-out fee when we do the work. If no work is done, a R650 call-out fee applies.

  • Swing gate kit

    Centurion Vantage 500 double swing kit

    R15 799incl. installation

    In the kit

    • 2 operators
    • wall box with charger
    • 12 V 7 Ah battery
    • mains isolator
    Our promise

    1-year guarantee on every motor kit we supply and install

  • Swing gate kit

    ET Wingo double swing kit

    R13 999incl. installation

    In the kit

    • 2 operators
    • 2 × 4-button ET remotes
    • 12 V 7 Ah battery
    • wall box with charger
    Our promise

    1-year guarantee on every motor kit we supply and install

Prices checked October 2026. Price includes the kit listed, standard installation on a gate or door that already runs freely, and our 1-year kit guarantee. Not included: a power point at the motor if there isn't one (a job for a registered electrician), extra rack, gate or door repairs, and accessories. These are quoted before any work starts.

Booking a gate technician in Saxonwold

On the job card, say whether the gate is clad, how long each leaf is and what it's doing; a photo helps. We work across Saxonwold, 2,557 people on 2.58 square kilometres at the 2011 census, from the streets by Zoo Lake to nearby Parkview, Forest Town and Parktown North. Same-day repairs are offered when the day allows.

Fault finder

What is your gate doing?

Pick what you're seeing for the likely causes, the safe checks you can do yourself, and when to stop and book. Taken from the manufacturers' own manuals.

What's it doing?

Likely causes

Gate motor · it's beeping

Most likely first

  1. The mains power to the motor is off, so it's running on its battery. Centurion and Gemini motors give two beeps (or two flashes) in a row; an ET Drive flashes twice and gives a one-second beep every 15 seconds.

  2. The battery is low. Centurion and Gemini motors give three beeps in a row; an ET Drive's status light flashes four times, without a beep.

  3. Something is between the safety beams. A Centurion motor gives a single beep every so often and won't close.

  4. The gate has hit something several times in a row, so the motor has stopped to protect itself. A Centurion keeps beeping until that's cleared.

  5. A holiday lockout or a time setting is blocking the remote: the motor beeps once when you press it and the gate doesn't move.

  6. On a Gemini, four beeps as the motor starts means the manual release lever isn't fully engaged.

Safe checks you can do

When to stop and book

If it keeps beeping with the power on and the beams clear, the battery, charger or controller needs a technician. Don't open the motor: Centurion warns that work by anyone unauthorised may void the manufacturer's warranty.

Questions

Gate motor questions in Saxonwold

Why does my solid swing gate stall when it's windy?

A clad leaf catches the wind like a sail: Centurion's tables show a fully clad gate can be moved against roughly half the wind of a palisade one. Read about wind.

How do I measure how far my swing gate opens?

Mark the ground 1 m from the hinge with the gate closed and again with it open, then measure between the marks: 1,414 to 1,521 mm is 90° to 99°. Read more.

Does a long swing gate need an electric lock?

Yes: Centurion calls for an electric lock on any leaf longer than 3 m, so the far end can't be pushed open. Read about locks.

Can a swing gate motor be fixed to an old brick pillar?

Usually, with chemical anchors for a masonry pillar in frequent use, provided the pillar is sound and the hinge isn't set too deep. Read about pillars.

Book a technician

Get a gate motor quote in Saxonworld

Job card

We WhatsApp or call you back. Fields marked (required) are needed.

Property type
When
Photos (optional, up to 4)

No call-out fee when we do the work. If no work is done, a R650 call-out fee applies.