Skip to content

24/7 emergency repairs across Gauteng

081 566 5451

Gate motors · Bedfordview

Gate motor repairs and installation in Bedfordview

A new motor for a sliding gate in Essexwold, a gate in Oriel that has come off its track, a motor in Morninghill that was never fitted properly and has failed again: we repair and install gate motors across Bedfordview.

Our promise

Six-month guarantee on our repairs

Our promise

1-year guarantee on every motor kit we supply and install

Bedfordview

Bedfordview and the areas around it. Every area we cover

Why installation decides everything

A gate motor that keeps failing has often been let down by how it went in: a rack bolted too tight onto the pinion, no end stops, a gate that drags on worn wheels, beams left out. The motor then strains, overheats or trips on every run, and the repairs never end. Getting the installation right prevents repairs like these, and it's the part of the job we take most care over. The steps below are from Gemini's manual for its 12 V DC slider, which we fit as a kit; Centurion and ET set out the same stages in their own manuals.

A technician fitting a sliding gate motor onto a concrete plinth beside a steel gate

The gate comes before the motor

Gemini's manual opens its installation section with the gate: it must be in good mechanical order, balanced, and open and close easily by hand. Its 500 kg rating assumes track wheels of at least 80 mm on roller bearings, running on a straight, level track. And it is blunt about one thing: the gate must never be able to run off its track, even if someone forces it.

So before a motor goes on, we push the gate along its whole travel by hand, and fix what we find: flat or seized wheels, a bent or loose track, guide rollers that bind, a frame that has twisted. That's why frame, panel, hinge and track repairs are such a large part of our gate work: they come first.

Fitting a sliding gate motor, step by step

  1. Position. With the gate closed, the motor is placed so that its pinion sits about 15 mm from the gate, square to it, and the spot is marked.
  2. Foundation. The base plate goes onto a concrete foundation, with conduit cast in for the cables, or is bolted to an existing foundation.
  3. Rack. Steel rack is welded on brackets no more than 600 mm apart; nylon rack is screwed to the gate. Either way, there's about 2 mm of vertical play between the rack and the pinion.
  4. Stoppers. Gemini makes them compulsory at both ends. They stop the gate overrunning, and the motor learns its limits from them.
  5. First runs. The gate closes slowly to one stopper and opens slowly to the other, learning both. If it heads the wrong way first, the motor's direction setting is changed.
  6. Obstruction test. The gate is held back by hand while it moves, and the sensitivity is adjusted until it stops and reverses as it should.
Gloved hands fitting a steel gear rack along the bottom of a sliding gate, the motor's pinion gear beside it

Power at the gate

The motor runs from its battery, and a small charger fed from the mains keeps the battery full. Gemini's manual insists that the supply is never wired straight in: there must be an isolator switch, usually within a metre of the motor, so it can be switched off before anyone works on it. The mains connection itself, and any new power point at the gate, is a job for a registered electrician. We fit and connect everything on the low-voltage side: the motor, battery, beams, keypads and receivers.

For the battery, Gemini's 12 V slider takes a 7 Ah or a 12 Ah battery, and Gemini suggests the 12 Ah for a busier gate or for longer back-up in power cuts.

Beams and settings, agreed with you

A motor's settings are choices about how your household uses the gate, so we agree them with you rather than leave the factory defaults:

  • Infra-red beams. Gemini says they must be fitted wherever the gate could hit a vehicle, a person or an animal. We recommend them on every gate.
  • Auto-close. Off, or a delay before the gate closes by itself; on Gemini's slider, from 2 to 60 seconds.
  • Townhouse function. Once the gate starts opening, no remote or button can stop it until the auto-close time is reached, so another press, yours or a neighbour's, can't halt it halfway. Beams and obstruction sensing still work.
  • Beam follower. If a car breaks the beams while the gate is still opening, the gate stops there, and closes behind the car once it's through.
  • Pedestrian opening. A part opening for people on foot, from a remote button or a keypad.
A technician aligning a safety beam on a short post beside a sliding gate

Gate motor repairs in Bedfordview

We repair Centurion, ET and Gemini motors, and others: batteries and chargers, control cards hit by surges, gearboxes, remotes and receivers, beams, and the gates themselves, from wheels and tracks to frames and hinges. A motor that was badly installed is corrected, not just restarted. All our spare parts are genuine, and every repair comes with our six-month guarantee on our repairs. The fault finder below has the checks that are safe to try first.

New gate motors in Bedfordview

Our kits are installed at a set price with battery, remotes and rack: the Gemini 12 V DC slider kit at R6 999 or the Centurion D5-Evo SMART sliding gate kit at R7 999 for a sliding gate up to 500 kg, and the ET Wingo single swing kit at R10 999 for a single swing gate. Prices checked October 2026. Your exact price is set in a free quote before any work starts. No call-out fee when we do the work. If no work is done, a R650 call-out fee applies.

  • Sliding gate kit

    Gemini 12 V DC slider kit

    R6 999incl. installation

    In the kit

    • Gemini DC slider (gates up to 500 kg)
    • 2 × 3-button Gemini remotes
    • 12 V 7 Ah battery
    • 4 m steel rack
    Our promise

    1-year guarantee on every motor kit we supply and install

  • Sliding gate kit

    Centurion D5-Evo SMART sliding gate kit

    R7 999incl. installation

    In the kit

    • D5-Evo SMART motor (gates up to 500 kg)
    • 12 V 7 Ah battery
    • 2 × 4-button NOVA remotes
    • 4 m steel rack
    Our promise

    1-year guarantee on every motor kit we supply and install

  • Swing gate kit

    ET Wingo single swing kit

    R10 999incl. installation

    In the kit

    • 1 operator
    • 2 × 4-button ET remotes
    • 12 V 7 Ah battery
    • wall box with charger
    Our promise

    1-year guarantee on every motor kit we supply and install

Prices checked October 2026. Price includes the kit listed, standard installation on a gate or door that already runs freely, and our 1-year kit guarantee. Not included: a power point at the motor if there isn't one (a job for a registered electrician), extra rack, gate or door repairs, and accessories. These are quoted before any work starts.

Compare two kits

SpecGemini 12 V DC slider kitCenturion D5-Evo SMART sliding gate kit
Price, installedR6 999R7 999
ForSliding gateSliding gate
In the boxGemini DC slider (gates up to 500 kg)D5-Evo SMART motor (gates up to 500 kg)
In the box2 × 3-button Gemini remotes12 V 7 Ah battery
In the box12 V 7 Ah battery2 × 4-button NOVA remotes
In the box4 m steel rack4 m steel rack
Guarantee1-year guarantee on every motor kit we supply and install1-year guarantee on every motor kit we supply and install

Booking a gate technician in Bedfordview

On the job card, say whether it's a new motor or a repair, give the motor's make if there is one, and describe what the gate does; a photo of the gate and motor helps. We work across Bedfordview, from Bedford Gardens, Bedford Park and St Andrews to Essexwold, Oriel, Senderwood, Morninghill and Dowerglen. Same-day repairs are offered when the day allows, and a gate stuck open is treated as urgent.

Fault finder

What is your gate doing?

Pick what you're seeing for the likely causes, the safe checks you can do yourself, and when to stop and book. Taken from the manufacturers' own manuals.

What's it doing?

Likely causes

Gate motor · it's beeping

Most likely first

  1. The mains power to the motor is off, so it's running on its battery. Centurion and Gemini motors give two beeps (or two flashes) in a row; an ET Drive flashes twice and gives a one-second beep every 15 seconds.

  2. The battery is low. Centurion and Gemini motors give three beeps in a row; an ET Drive's status light flashes four times, without a beep.

  3. Something is between the safety beams. A Centurion motor gives a single beep every so often and won't close.

  4. The gate has hit something several times in a row, so the motor has stopped to protect itself. A Centurion keeps beeping until that's cleared.

  5. A holiday lockout or a time setting is blocking the remote: the motor beeps once when you press it and the gate doesn't move.

  6. On a Gemini, four beeps as the motor starts means the manual release lever isn't fully engaged.

Safe checks you can do

When to stop and book

If it keeps beeping with the power on and the beams clear, the battery, charger or controller needs a technician. Don't open the motor: Centurion warns that work by anyone unauthorised may void the manufacturer's warranty.

Questions

Gate motor questions in Bedfordview

How far apart should the brackets on a gate rack be?

For a steel rack on Gemini's DC slider, no more than 600 mm apart, with about 2 mm of play between the rack and the pinion. Read the fitting steps.

Does a gate motor need its own isolator switch?

Yes. Gemini's manual calls for one, usually within a metre of the motor, so the power can be switched off before anyone works on it. Read about power at the gate.

What does the townhouse function on a gate motor do?

On a Gemini slider, it stops remotes from halting the gate once it starts opening, until the auto-close time is reached; beams and obstruction sensing still work. Read about settings.

Should my Gemini slider have a 7 Ah or a 12 Ah battery?

Either fits. Gemini suggests the 12 Ah for a busier gate or for longer back-up in power cuts. Read about power at the gate.

Book a technician

Get a gate motor quote in Bedfordview

Job card

We WhatsApp or call you back. Fields marked (required) are needed.

Property type
When
Photos (optional, up to 4)

No call-out fee when we do the work. If no work is done, a R650 call-out fee applies.