Electric fences · Randburg
Electric fence repairs and new fences in Randburg
A keypad in Ferndale with an alarm light that won't go out, a fence in Bromhof that trips whenever the gate opens, a Nemtek energiser in Boskruin that's dead after a storm: we repair electric fences across Randburg and install new ones. 2-year warranty and a compliance certificate on every new electric fence we install.
2-year warranty and a compliance certificate on every new electric fence we install
Six-month guarantee on our repairs
Randburg and the areas around it. Every area we cover
Your Nemtek keypad, explained
A Randburg fence is run day to day from a keypad by the door, and Nemtek's keypads work on levels of user, set out in Nemtek's own manual:
- One master user, who can switch the fence on and off, bypass alarms and set everyone else's PIN. The factory master PIN is 1234, and leaving it unchanged means anyone who knows it can switch your fence off.
- Normal users, who can switch the fence on and off and reset alarms but can't change how the energiser works. They have no factory codes; the master sets them.
- Reset users, who can only reset alarms, never switch the fence off. Useful for staff or a garden service.
To switch the fence on or off, you enter your four-digit PIN and press #. Don't pause more than about five seconds between digits, or the keypad rejects the PIN; a wrong PIN gets five beeps. Press # and start again if you slip.

When the fence alarms at night
An alarm at 2 a.m. is when the keypad matters most. Nemtek's manual sets out what happens:
- Enter your PIN and press #. That silences the siren and the buzzer, and switches the fence off.
- Read the alarm light. One of the alarm lights shows the source. If it's flashing, the fault is still there; if it's lit steadily, the fault has cleared and switching the fence back on clears the memory.
- Don't go looking alone. If your armed response company is linked, let them check the boundary.
- If it keeps alarming, with a flashing light that won't clear, the fault is on the fence: switching it on and off won't stop it. The master user can bypass the alarm for the night, and we find the cause in the morning.
Two things catch people out. Gate inputs stay active even with the fence switched off, so an open gate can still alarm unless the gate alarm is bypassed. And after a total power failure, with the mains off and the battery flat, the energiser comes back in the state it was in before.
Low voltage, children and pets
Nemtek's keypads let the master user drop the fence into a low-voltage mode, meant for when children are playing near it; the red ON light flashes while it's in that mode. One catch from the manual: on a two-zone energiser, the keypad can't tell the zones apart in low-voltage mode, so an alarm doesn't say which side tripped. Switch back to full voltage when the children are inside.
Upgrading an older keypad or energiser
Some of Randburg's fences went up years ago with an energiser switched on and off at the box, or an early keypad that has started to misbehave. Worthwhile upgrades:
- A keypad by the door, or a second one by the bedroom, on Nemtek's keypad cable, which can run up to 100 m from the energiser.
- A newer energiser with a display, such as a Druid LCD, that tells you the fence's condition and which zone tripped, in place of one that only beeps.
- A second zone on a long boundary, so a back-wall alarm doesn't send you round the whole property.
- New PINs: change the master PIN from the factory 1234, and set fresh codes whenever someone who had one moves on.
An upgrade that adds to or alters the fence itself, such as new lines or a longer run, brings in a new certificate.
Electric fence repairs in Randburg
When the keypad can't settle it, we test the fence zone by zone with a fence tester and repair what we find:
- Plants and branches across the lines, especially in Randburg's leafier older suburbs.
- Broken or slack wire, joined properly with ferrules or clamps.
- Cracked insulators that arc and leak current in the rain.
- Gate switches out of line, so a gate reads as open when it's shut.
- Energisers with a blank display or no output, especially after lightning, repaired on the bench or replaced.
- Batteries that no longer carry the fence through load-shedding.
- Keypads that have lost contact with the energiser.
All our spare parts are genuine, and every repair comes with our six-month guarantee on our repairs. The safe checks for you to do first are in the fault finder below; never touch the fence or open the energiser.
Nemtek and JVA energisers
Randburg searches for Nemtek by name, and we repair and replace Nemtek's Druid and Merlin energisers alongside JVA's Z-series. A Druid 13 LCD is about R2 940–R3 280 (Takealot, NeonSales) and a Merlin 4i with keypad about R3 750 (Takealot) in shops; a JVA Z11 about R3 070 (Takealot). Repairing an energiser typically runs R800–R2 500 (Kandua), so a repair is worth pricing before a replacement. The models are compared on our energiser page.

New electric fences in Randburg
A new fence starts with a walk along the wall to agree the lines, the zones and where the energiser, keypad and earth spikes go. It's built to the rules Nemtek and JVA print in their manuals: warning signs at every gate and at least every 10 m, no barbed or razor wire near the live lines, gates that open without a shock, at least 2.5 m between fences on different energisers, and the alarm panel linked through an isolation relay. Certified electric fence installer, and the fence is handed over with its certificate and with the keypad's factory PINs changed. The process is on electric fence installation.
Typical market prices, not ours: a 8-line wall-top fence installed costs R115–R125 a metre (published price lists of Gauteng installers) a metre on Gauteng installers' price lists, and cost guides put a typical suburban home's 50 to 100 m fence, certificate included, at R12 000–R25 000 (Kandua). Prices checked October 2026. Your exact price is set in a free quote before any work starts. No call-out fee when we do the work. If no work is done, a R650 call-out fee applies.

Selling a Randburg property
A sale of a property with an electric fence needs an Electric Fence System Certificate. We inspect the fence, issue the certificate when it passes, and price what needs fixing when it doesn't. Book it as soon as the property is listed, and keep the certificate with the property's papers: a careful buyer will check that the fence it describes is the fence on the wall. More on electric fence certificates.
Booking a fence technician in Randburg
On the job card, tell us the energiser and keypad make, which alarm light is showing and whether it's flashing or steady. We work across Randburg, from Ferndale, Robindale and Windsor to Bromhof, Boskruin and Craighall. Same-day repairs are on offer whenever the day's bookings allow, and a fence you've had to bypass for the night counts as urgent.
Fault finder
What is your fence doing?
Pick what you're seeing for the likely causes, the safe checks you can do yourself, and when to stop and book. Taken from the manufacturers' own manuals.
What's it doing?
Likely causes
Electric fence · the alarm keeps going off
Most likely first
The fence voltage has dropped below the alarm level: something is touching the wires, or plants have grown into the fence.
The gate input is open: the gate isn't fully closed.
The fence condition is poor: dirty or failed insulators, or wet insulators after rain.
Safe checks you can do
When to stop and book
Never touch the fence wires or open the energiser. If the alarm won't clear, we'll find the fault on the fence.
From the official manuals: Nemtek Druid 25 and 28 user manual, Nemtek Druid LCD user manual.
Questions
Electric fence questions in Randburg
What does a flashing alarm light on my Nemtek keypad mean?
Nemtek's manual says a flashing alarm light means the fault is still there; a steady one means it has cleared, and switching the fence back on clears the memory. A flashing light that won't clear is a fault on the fence. Read about alarms at night.
Why does my fence alarm when the gate opens, even with the fence off?
The gate inputs stay active when the energiser is switched off, so an opening gate can still trigger the alarm unless the gate alarm is bypassed from the keypad. If it alarms with the gate shut, the gate switch may be out of line. Read about the keypad.
Can I give my domestic worker a keypad code that can't switch the fence off?
Yes. Nemtek's keypads have reset users, who can reset alarms but can't change whether the fence is on or off. The master user sets the code. Read about keypad users.
Do you repair Nemtek energisers in Randburg?
Yes, Druid and Merlin energisers and their keypads, and JVA's Z-series. Cost guides put an energiser repair at less than most new units, so we price the repair first. Read about energisers.
Book a technician
Get an electric fence quote in Randburg
Job card
We WhatsApp or call you back. Fields marked (required) are needed.