Skip to content

24/7 emergency repairs across Gauteng

081 566 5451

Electric fences · Morningside

Electric fence repairs in Morningside, busy by day and armed by night

A school fence that should be gentler while children are about, a clinic's energiser that needs to arm itself at closing time, a home fence whose readings creep up month after month: we repair and install electric fences across Morningside. 2-year warranty and a compliance certificate on every new electric fence we install.

Our promise

2-year warranty and a compliance certificate on every new electric fence we install

Our promise

Six-month guarantee on our repairs

Morningside

Morningside and the areas around it. Every area we cover

Fences that are busy by day

Morningside isn't only homes. Alongside them are clinics, schools, offices, hotels and shopping centres, many of them full of people by day and empty at night. A fence on such a site has two jobs that pull in different directions: to be safe and calm while staff, patients, pupils and visitors are about, and to be fully armed when everyone has gone home.

JVA's Z-series energisers have features made for exactly that, and their manual explains them clearly.

A technician on a ladder holding a fence tester against the strands of an electric fence on a boundary wall

Conventional or bi-polar

JVA describes two ways of wiring the fence itself:

  • Conventional: live and earth wires alternate along the fence. Touch a live wire and an earth wire together, and the circuit closes through you.
  • Bi-polar: every wire is live. The energiser sends synchronised positive and negative pulses down alternate wires, so the shock comes from touching any two neighbouring wires.

JVA's Z11 and Z13 run conventional fences; the Z14, Z18 and Z114 can run either. The display shows which: in conventional mode, arrows appear at the top, and in bi-polar mode, it shows the positive and negative return voltages instead. Which suits a site depends on the fence's design and how it's earthed, and it's settled when the fence is planned.

Low power by day, full power by night

Every Z-series energiser has a low power mode, in which the live wires run at a much lower voltage, about 500 V peak by JVA's figure. The fence still detects a cut, a short or someone climbing; JVA's words are detection together with public safety. While it's in low power, the energiser's Armed light flashes rather than staying on.

What makes it practical on a busy site is the control inputs. Each Z-series energiser has two, and one can be set to switch the energiser between high and low power while it's armed. Wired to a timer, or to the building's alarm system, that lets the fence run on low power during working hours and switch to full power when the building is locked up, with nobody having to remember. The other input arms and disarms the fence the same way.

A control input can also be a gate input: wired to a gate switch, it raises an alarm if the gate stays open longer than the entry and exit delay, and while the fence is disarmed it can simply chime when the gate opens.

A reading that warns you early

On JVA's Z13, Z14 and Z18, the display shows the voltage going out to the fence and coming back from its far end, and every 4 to 5 seconds, the stored energy the energiser is using to hold that voltage. JVA explains what that number means: on a fence in good condition it's low, and as load comes onto the fence, from plants, a cracked insulator or a wire touching a bracket, it rises to keep the voltage up.

The two voltages tell their own story. JVA calls them the feed, where the high voltage leaves the energiser for the start of the zone, and the return, where it arrives back from the zone's far end to be checked. A healthy zone returns close to what it was fed. A return that falls well below the feed points to something between the two ends drawing current away, and if it drops below the alarm level, the energiser raises a fence alarm. Reading the two numbers side by side is often the quickest way to tell a fault on the fence from a fault in the energiser.

The stored energy makes an early warning. Note the stored energy on a day the fence is in good order; if it creeps up over the following weeks, the fence is losing current somewhere, and it's cheaper to find it then than after the first false alarm.

A technician shining a torch on the terminals of an open electric fence energiser box in a garage

How a JVA energiser goes up

JVA's installation steps are short, and each one is there for a reason:

  1. The right place. Outdoors, the energiser goes inside an equipment box, and never in direct sunlight.
  2. Flat against the wall. The housing is mounted so all four of its mounting holes sit against the wall; an open hole would let someone poke a metal object inside and get a shock.
  3. Sealed. The cable entry is sealed with neutral-cure silicone.
  4. A safe start. The energiser doesn't start the first time it's powered up, whatever its control inputs say, so it can't come on unexpectedly during installation.
  5. Tested. Once armed, the display must show the fence voltage, and a short anywhere on the fence must raise the alarm.

On a school, clinic or office fence

  • Who controls it. Name the people who may arm, disarm and silence the fence, and give each their own access, so codes don't pass around the staff room.
  • A schedule that matches the building, set once, through a control input, so low power and full power follow opening hours.
  • The alarm going somewhere, to a security company or the building's own alarm, so a night-time breach isn't heard only by the neighbours.
  • A service at least yearly, with the readings recorded each time, so a creeping fault shows up in the numbers.

Electric fence repairs in Morningside

We repair JVA and Nemtek energisers, keypads, control-input wiring, timers and alarm links, and the fences themselves: broken wires, cracked insulators, bent brackets, earth spikes, gate switches, sirens and strobes. All our spare parts are genuine, and every repair comes with our six-month guarantee on our repairs. The safe checks to try first, none of which involve touching the wires, are in the fault finder below.

New fences and certificates

A new fence for a home or a business is planned on site with you, including the wiring style, the zones and the schedule, built to the rules JVA and Nemtek print in their manuals, tested along every zone and handed over with its certificate. Certified electric fence installer. For a certificate alone, see electric fence certificates.

Typical electric fence prices

Market prices in Gauteng, from installer price lists and cost guides, not ours:

  • 10-line wall-top fence, installed: R130–R145 a metre (published price lists of Gauteng installers)
  • 18-line freestanding fence, installed: R205–R225 a metre (published price lists of Gauteng installers)
  • Simple repairs (insulators, a broken wire) including call-out: R700–R1 400 (Kandua)
  • Inspection and certificate for a fence that already complies: R850–R1 500 (Kandua, Completo)

Prices checked October 2026. Your exact price is set in a free quote before any work starts. No call-out fee when we do the work. If no work is done, a R650 call-out fee applies.

Booking a fence technician in Morningside

On the job card, give the energiser's make and model, what its display shows, and whether it's a home or a business; for a business, add who will meet us and when the site is quiet. Morningside had 15,723 residents on 6.24 square kilometres at the 2011 census, and we cover all of it, out to Morningside Manor, Edenburg and Sunset Acres. Same-day repairs are offered when the day allows, and a fence down at night is treated as urgent.

Fault finder

What is your fence doing?

Pick what you're seeing for the likely causes, the safe checks you can do yourself, and when to stop and book. Taken from the manufacturers' own manuals.

What's it doing?

Likely causes

Electric fence · the alarm keeps going off

Most likely first

  1. The fence voltage has dropped below the alarm level: something is touching the wires, or plants have grown into the fence.

  2. The gate input is open: the gate isn't fully closed.

  3. The fence condition is poor: dirty or failed insulators, or wet insulators after rain.

Safe checks you can do

When to stop and book

Never touch the fence wires or open the energiser. If the alarm won't clear, we'll find the fault on the fence.

Questions

Electric fence questions in Morningside

What is a bi-polar electric fence?

One where every wire is live, with the energiser sending positive and negative pulses down alternate wires; a conventional fence alternates live and earth wires. Read about wiring.

Can an electric fence run on low power during the day?

Yes: JVA's Z-series low power mode runs the live wires at about 500 V peak, and a control input can switch it on a timer or from an alarm system. Read about low power.

What does stored joules mean on a JVA energiser?

The energy it's using to hold the fence voltage. It's low on a healthy fence and rises as load comes onto it, so a creeping figure is an early warning. Read about the display.

Why didn't my JVA energiser start when it was first powered up?

It's designed not to: JVA's Z-series won't start on first power-up whatever its control inputs say. Arm it from the keypad or a control input. Read about installation.

Book a technician

Get an electric fence quote in Morningside

Job card

We WhatsApp or call you back. Fields marked (required) are needed.

Property type
When
Photos (optional, up to 4)

No call-out fee when we do the work. If no work is done, a R650 call-out fee applies.