Skip to content

24/7 emergency repairs across Gauteng

081 566 5451

Electric fences · Edenvale

Nemtek energisers and electric fence repairs in Edenvale

A Nemtek Druid showing an alarm nobody can explain in Eastleigh, a fence gone quiet after a storm in Edenglen, a new fence for a cluster in Hurlyvale: we repair Nemtek and JVA energisers and the fences they run across Edenvale, and install new ones. 2-year warranty and a compliance certificate on every new electric fence we install.

Our promise

2-year warranty and a compliance certificate on every new electric fence we install

Our promise

Six-month guarantee on our repairs

Edenvale

Edenvale and the areas around it. Every area we cover

Nemtek energisers in Edenvale

Nemtek is the make people in Edenvale search for by name. The Nemtek range we repair and replace:

  • Druid 13 and 15 LCD, single-zone energisers for a house fence.
  • Druid 25 and 28 LCD, two-zone models; two can be linked as master and slave to give four zones on a long boundary.
  • Druid 114 LCD, a 14-joule model for long or heavily lined fences.
  • Merlin energisers and keypads, on older installations.

Each Druid has a display on the box and, usually, a keypad indoors. Between them they tell you more about the fence than most people realise, which is why we read them before we touch anything. JVA's Z-series energisers get the same treatment, and both makes are compared on our energiser page.

A technician shining a torch on the terminals of an open electric fence energiser box in a garage

What your Druid's display is saying

Nemtek's manual sets out what each symbol on a Druid LCD means. The ones that prompt most calls:

Nemtek Druid LCD symbols, from Nemtek's user manual
SymbolWhat it means
A number from 0 to 9The fence's condition: higher is better
!Fence voltage is below the check level
xFence voltage is below the alarm level
0The fence is switched off
loThe fence is on low power
sSilent alarm: no siren or strobe, only the beeper
oA gate is open
tThe cover is, or was, opened: possible tampering
The service symbolShown for a long time, the energiser needs servicing

The alarm symbols come in two forms: one says the condition is still there and needs fixing first; the history symbol says it happened and has cleared. A condition number that keeps falling is the fence asking for maintenance before it starts alarming.

Keeping the fence in good condition

Nemtek's advice for a high condition number is plain fence-keeping: cut back plants that reach the wires, and clear dead slugs, snails, spiders and insects off the insulators, where they leak current to earth, and replace insulators that have failed. In the older streets of Eastleigh and Illiondale, with their established gardens, creepers and hedges are the obvious first suspect.

Do that from a safe distance with the fence switched off at the keypad, and never touch a live line. Two Druid features help day to day:

  • Low power turns the fence down to a far less painful level, for example while children are playing near it; the installer sets how low.
  • Silent alarm stops the siren and strobe from going off, leaving only the internal beeper, which is useful while a fence is being tested.

Both show on the display, so check for "lo" or "s" if the fence seems weak or an alarm made no noise.

Electric fence repairs across Edenvale

When the display can't settle it, we test the fence zone by zone and repair what's found:

  • Broken or slack wires, joined with the right ferrules or clamps, not twisted together.
  • Cracked or burnt insulators, replaced along the run.
  • Earth faults: spikes corroded, disconnected or too close to the house's own earth.
  • Gate switches that trip the alarm every time a gate opens.
  • Energisers with a blank display, no output or a board damaged by lightning, repaired on the bench or replaced.
  • Keypads that have stopped talking to the energiser.

All our spare parts are genuine, and every repair comes with our six-month guarantee on our repairs. The checks that are safe to do yourself are in the fault finder below; opening the energiser isn't one of them, because it works at a dangerous voltage.

Silencing, resetting and the factory PINs

To silence a Druid LCD that's sounding, hold the Nemtek tab over the Nemtek logo on the front until the short beep and then the longer one. Alarm history clears the same way, or by switching the energiser off and on; an alarm that's still present clears only once its fault is fixed.

Druids leave the factory with a master PIN of 1234, which switches the fence on and off, and a reset PIN of 5555, which can silence and clear alarms but can't turn the fence off. If yours still use those numbers, change them: anyone who knows the defaults can switch your fence off. A full factory reset needs the energiser opened and its power disconnected, so that's a job for us.

Batteries and load-shedding

A Druid LCD runs from a 12 V 7 Ah sealed battery that the mains keeps charged, and Nemtek puts a new, fully charged one at typically more than 24 hours of running, less on a fence in poor condition. If the battery goes completely flat, the Druid keeps its settings and comes back as it was when the power returns. A fence that now drops out partway through load-shedding has a battery that's worn out. A replacement battery is R230–R450 (Takealot) in shops; we test the old one and fit the new one on the same visit.

New electric fences in Edenvale

For a new fence, we walk the boundary, agree the lines, zones and energiser, then build it to the rules Nemtek and JVA print in their manuals: warning signs at every gate and at least every 10 m, no barbed or razor wire near the live lines, gates that open without a shock, and earth spikes at least 10 m from any other earth system. A cluster or townhouse complex in the Avenues shares one perimeter fence, so the body corporate books it and the energiser sits at the gate. Certified electric fence installer, and every new fence is handed over with its certificate; selling an existing one needs a certificate too, explained on electric fence certificates.

A technician on a ladder holding a fence tester against the strands of an electric fence on a boundary wall

What Nemtek energisers and fencing typically cost

Typical market prices, not ours:

Energisers and electric fencing, typical prices
WhatTypical price
Nemtek Druid 13 LCD, in shopsabout R2 940–R3 280 (Takealot, NeonSales)
Nemtek Druid 15 LCD, in shopsabout R2 740–R3 540 (Takealot, NeonSales)
Nemtek Druid 28 LCD, in shopsabout R5 190–R5 210 (Takealot, NeonSales)
Nemtek Merlin 4i with keypad, in shopsabout R3 750 (Takealot)
Energiser repairR800–R2 500 (Kandua)
6-line wall-top, installedR95–R115 a metre (published price lists of Gauteng installers)

Prices checked October 2026. Your exact price is set in a free quote before any work starts. No call-out fee when we do the work. If no work is done, a R650 call-out fee applies.

Booking a fence technician in Edenvale

On the job card, tell us the energiser's make and model, what the display or keypad shows, and whether the fence alarms, is weak or has gone quiet. A photo of the display helps. We work across Edenvale, from Croydon and Sunnyridge to Lombardy East and Sunningdale.

Same-day repairs are part of the normal week here, whenever the day's bookings allow, and a fence alarming through the night is an emergency: tick "It's urgent".

Fault finder

What is your fence doing?

Pick what you're seeing for the likely causes, the safe checks you can do yourself, and when to stop and book. Taken from the manufacturers' own manuals.

What's it doing?

Likely causes

Electric fence · the alarm keeps going off

Most likely first

  1. The fence voltage has dropped below the alarm level: something is touching the wires, or plants have grown into the fence.

  2. The gate input is open: the gate isn't fully closed.

  3. The fence condition is poor: dirty or failed insulators, or wet insulators after rain.

Safe checks you can do

When to stop and book

Never touch the fence wires or open the energiser. If the alarm won't clear, we'll find the fault on the fence.

Questions

Electric fence questions in Edenvale

Do you repair Nemtek energisers in Edenvale?

Yes, the Druid 13, 15, 25, 28 and 114 LCD, older Merlin units and their keypads, and JVA energisers too. We read the display first, test the fence, then repair the energiser on the bench or replace it. Read about Nemtek energisers.

What does the t on my Nemtek display mean?

Nemtek uses it to say the energiser's front cover is, or was, opened: possible tampering. If nobody has opened it, have it looked at, and check the fence is still on. See every symbol.

Why is my Nemtek fence condition number low?

Current is leaking from the fence, most often through plants touching the wires or insects and snails on the insulators, or through failed insulators. Clear what you safely can with the fence off, then book a test if it doesn't climb. Read about fence condition.

How much is a Nemtek Druid energiser?

In shops, a Druid 13 LCD is about R2 940–R3 280 and a two-zone Druid 28 LCD about R5 190–R5 210 (prices checked October 2026), before fitting and setting it up. See typical prices.

Do you install electric fences in Edenglen and Eastleigh?

Yes, across Edenvale, including Edenglen, Eastleigh, Hurlyvale and Illiondale: wall-top fences for houses and shared perimeters for clusters, each handed over with its certificate. Read about new fences.

Book a technician

Get an electric fence quote in Edenvale

Job card

We WhatsApp or call you back. Fields marked (required) are needed.

Property type
When
Photos (optional, up to 4)

No call-out fee when we do the work. If no work is done, a R650 call-out fee applies.