Skip to content

24/7 emergency repairs across Gauteng

081 566 5451

Guides · Gate motors

Gate safety beam not working: why, and what to check

Safety beams are the pair of small boxes either side of your driveway that stop the gate closing on a car or a person. When they fail, the gate usually refuses to close, which is the beams doing their job: a gate motor treats a beam it can't see as a beam that's blocked. Here's how beams go wrong, how to tell from the gate's behaviour, and what you can safely check.

Our promise

Six-month guarantee on our repairs

Emergency

24/7 emergency repairs across Gauteng

A technician aligning a safety beam on a short post beside a sliding gate

How beams talk to the gate motor

One unit sends an invisible infrared beam across the opening; the other receives it. While it receives the beam, it tells the motor the way is clear. Break the beam, and the motor is told something is in the way. On most gates the beams only act while closing: Centurion's guide, for example, explains that a blocked closing beam stops an open gate from closing at all, and makes a closing gate stop and open again.

That design is deliberately fail-safe. A beam with no power, a broken wire or a lens it can't see through looks exactly like a blocked beam, so the gate stays open rather than closing on someone. That's why "beams not working" almost always shows up as "gate won't close".

A technician aligning a safety beam on a short post beside a sliding gate

What the gate does when the beams fail

  • It opens but won't close, or ignores the close command entirely.
  • It starts closing, then stops and opens again.
  • Auto-close doesn't happen, and the gate stays open.
  • It beeps or shows a message: on ET's Drive motors, irb or Beam interrupted; on a Drive 1000 setting up beams, Beam Test, Not switching or Illegal wiring; on Hydro Doors' garage openers, two beeps when you try to close, or E6 on a Digi 7.
  • It closes only if you hold the button, on motors set up that way.

If the gate closes perfectly well and simply never stops for anything, that's the opposite and more dangerous fault: the beams may have been bypassed or switched off. That needs fixing straight away.

Why beams stop working

In rough order of how often we find them:

  1. Something in the way: a wheelie bin, a pot plant, a parked car's bumper, long grass or a spider web across the lens.
  2. Dirty or wet lenses: dust, mud splashed from the driveway, bird droppings or condensation.
  3. Knocked out of line: a car, a lawnmower or a gardener's broom can twist a beam just enough to miss its partner. Sun-damaged plastic housings crack and sag.
  4. Low sun: at certain times of year, sunrise or sunset shining straight into the receiver can blind it for a few minutes a day.
  5. No power: a cut or chewed cable, corroded connections at the post, or a fault on the motor's accessory supply.
  6. Wiring after a storm or a new installation: surge damage, or wiring the motor doesn't accept. ET's Drive 300 manual, for instance, lists the beam circuit's end-of-line resistor as one of the checks.
  7. Switched on with no beams fitted: some motors and garage openers must have the beam input switched off if there are no beams, or the door opens but never closes.

Safe checks you can do

  1. Clear the line between the two units, and look at the ground and gate, not just eye level.
  2. Wipe both lenses with a soft, damp cloth.
  3. Look for indicator lights on the beam units, if they have them. A light that changes when you block the beam with your hand shows the beam is aligned and powered.
  4. Check they're facing each other. Sight along them; one that's been knocked will often be visibly crooked.
  5. Note the time of day. If the gate only refuses to close for a few minutes at sunrise or sunset, the sun is the likely culprit.
  6. Read the motor's display or status light, if it has one.

Don't open the beam housings or the motor, strip wires or bridge the beam terminals to get the gate closed. A gate without working beams can crush a child or a car.

Where beams should sit

Beam height is a trade-off. Hydro Doors' advice for garage doors puts it simply: low enough to protect toddlers and pets, but not lower than the underside of a typical car. On a driveway gate, the same thinking applies, and many installations use two pairs: one low for people and animals, one at bumper height for cars.

Beams that are too high miss a small child; beams that are too low are triggered by grass, leaves and the gardener's hose. If yours keep tripping on nothing, their height and position may be the real problem.

Never bypass them to get the gate working

When beams fail, it's tempting to have them bypassed so the gate works again. Don't. Manufacturers treat beams as essential: ET's manuals make them compulsory whenever auto-close is used, and on a Drive 1000 auto-close won't even switch on without them. A gate that closes by itself with no beams is the most dangerous kind of gate motor installation. We repair or replace beams; we don't bypass them. More on safety beams.

Repairs and what they typically cost

Most beam faults are a clean, a realignment or a reconnected wire. When a unit has been damaged by a car, the sun or a surge, it's replaced, usually as a pair. Typical figures in the market:

  • Safety beams replaced: R600–R1 200 (Kandua)
  • Beams supplied and fitted: beams supplied and fitted R750–R1 500 (Kandua installation guide)
  • In shops, ET Blue Eyes about R570 (Takealot), Centurion i5 about R650 (Takealot) and Photon about R900–R1 050 (Takealot)

These are the market's figures, not ours. Prices checked October 2026. Every repair carries our six-month guarantee on our repairs. Your exact price is set in a free quote before any work starts. No call-out fee when we do the work. If no work is done, a R650 call-out fee applies.

Fault finder

What is your gate doing?

Pick what you're seeing for the likely causes, the safe checks you can do yourself, and when to stop and book. Taken from the manufacturers' own manuals.

What's it doing?

Likely causes

Gate motor · it starts closing, then opens again

Most likely first

  1. Something breaks the safety beams as the gate closes.

  2. The motor feels resistance and treats it as a collision: something on the rail, a stiff wheel, or the gate running badly.

Safe checks you can do

When to stop and book

If the path is clear and it still reverses, the collision settings or the beams need a technician.

Questions

Questions about beams that stop working

Why won't my gate close because of the beams?

Because a gate motor treats a beam it can't see as a blocked beam: something in the way, a dirty lens, a beam knocked out of line, low sun or a power fault all look the same to it. Clear and wipe them first. See the causes.

Can sunlight affect gate safety beams?

Yes: low sun shining straight into the receiver at sunrise or sunset can blind it for a few minutes a day, so the gate won't close at the same time every day. Repositioning or shading the receiver usually cures it. See the causes.

Is it safe to bypass gate safety beams?

No. Beams are what stop a closing gate on a person or a car, and manufacturers make them compulsory with auto-close. Have them repaired instead. Read why.

Book a technician

Get a gate motor quote

Job card

We WhatsApp or call you back. Fields marked (required) are needed.

Property type
When
Photos (optional, up to 4)

No call-out fee when we do the work. If no work is done, a R650 call-out fee applies.