Skip to content

24/7 emergency repairs across Gauteng

081 566 5451

Guides · Electric fencing

Electric fence after load shedding: why the energizer isn't working

Load shedding is when electric fences show their weak spots. An energizer runs on its battery through the outage, and if the battery is tired, the fence goes dead before the power comes back, or comes back with warnings, beeps and low readings. Here's what an electric fence energizer does during and after a power cut, what's normal, what isn't, and what to check.

Our promise

2-year warranty and a compliance certificate on every new electric fence we install

Emergency

24/7 emergency repairs across Gauteng

A driveway at night during a power cut, a sliding gate open and the houses around it dark

Does an electric fence work during load shedding?

Yes, as long as its battery lasts. A security energizer runs from the mains with a battery behind it, usually a 12 V sealed lead-acid. When the mains fails, the battery takes over and the fence stays live. Nemtek says a new, fully charged battery typically carries a Druid LCD for more than 24 hours, less on a fence in poor condition, because a leaking fence makes the energizer work harder.

What changes in a power cut:

  • The power light goes out or a mains-fail warning shows. On a Nemtek Wizord, the power LED goes off; on a Druid, a mains symbol changes.
  • The fence stays armed. JVA's manual is explicit that a mains failure doesn't disarm its Z-series energizers.
  • As the battery runs down, the energizer may switch to a lower-power mode to keep going: JVA gives four warning beeps first.

Dead after load shedding: the battery ran out

If the outage outlasted the battery, the energizer eventually stops. JVA's Z-series keeps going in low power until the battery falls too far, then stops; Nemtek's Wizord notes that a long enough failure shuts the unit down with no indication at all.

When the mains returns, most energizers recover by themselves:

  • JVA re-arms itself, after four warning beeps, once the mains is back and the battery has recovered enough.
  • Nemtek Merlin restores whatever state it was in before the total power failure.
  • Nemtek Druid keeps all its user and installer settings even when the battery runs completely flat.

So a fence that's dead straight after the power returns may just need time. If it's still dead hours later with the mains on, check the plug, its switch and the distribution board, then call us.

A driveway at night during a power cut, a sliding gate open and the houses around it dark

Warnings, beeps and service lights afterwards

After a long outage, it's common to see:

  • A mains-fail history symbol or light, simply recording that the power failed while you were away. Clearing the alarm memory removes it.
  • A service light or warning while the battery recharges. Nemtek says a service condition can appear for a short while after a prolonged mains failure; if it persists, the battery may need replacing or something else needs attention.
  • Beeping from the energizer or keypad as the battery warning sounds. See electric fence beeping.
  • A lower fence reading than usual while the energizer is still running on a weak battery.

Give it a full day on mains. Warnings that clear by then were the outage; warnings that stay are a fault.

The real problem: a battery worn out by load shedding

Every outage drains the battery, and every restoration recharges it. Batteries can only take so many deep cycles, and heavy load shedding uses them up in months rather than years. The signs:

  • the fence goes dead earlier in each outage;
  • warnings keep coming back after a full day on mains;
  • the energizer's own battery test fails: on a Nemtek Merlin, master PIN then \* 6 # runs the mains off for 20 minutes and lights the battery service light if the battery can't cope.

A new battery of the type the maker specifies is usually the fix, and it's a quick job for us, because it means opening the energizer. JVA, for example, specifies a 12 V sealed lead-acid battery for its Z-series; it's not a case of fitting any battery that fits.

Surges when the power comes back

The moment power is restored can bring a surge that damages electronics. Good energizers are built for it: Nemtek's Wizord, for example, has lightning and surge protection on its mains and its fence outputs. But protection has limits, and an energizer, keypad or siren that died exactly when the power returned, with a burnt smell or no display at all, may have been damaged. That's a repair or replacement, and sometimes a claim on your household insurance, so keep a note of when it happened.

Safe checks you can do

  1. Make sure the mains is back at the energizer: the plug, its switch and the distribution board.
  2. Wait, with the mains on, for the battery to recover. Many energizers re-arm themselves.
  3. Read the display or lights, and note any battery or service warning.
  4. Clear the alarm memory with your code once the mains is back, and see if it comes back.
  5. Run a battery test if your keypad has one.

Don't open the energizer or touch the fence wires. If the fence is dead overnight and your property depends on it, that's covered by our 24/7 emergency repairs across Gauteng.

When to call us

Call us when the fence is still dead hours after the power returned, the battery warning won't clear after a day on mains, the fence dies early in every outage, or something failed when the power came back. We test and replace batteries, repair energizers, keypads and sirens, and can help you plan for load shedding with the right battery. Every repair carries our six-month guarantee on our repairs. No call-out fee when we do the work. If no work is done, a R650 call-out fee applies. More on fences that won't work for other reasons is on electric fence not working.

Questions

Questions about fences and load shedding

Does an electric fence work during load shedding?

Yes, on its battery: the fence stays armed and live until the battery runs low, which on a new, fully charged Nemtek Druid battery is typically more than 24 hours, less on a fence in poor condition. A worn battery may not last one outage. Read what happens during an outage.

Why is my electric fence energizer not working after load shedding?

Most often the battery ran flat during the outage and hasn't recovered yet, or it's worn out by repeated outages; sometimes a surge when the power returned damaged it. Check the mains is back and give it time, then have the battery tested. See the battery.

Why is my electric fence beeping after a power cut?

Usually a battery or service warning while the battery recharges, or a mains-fail record; it should clear within a day on mains. If it doesn't, the battery may need replacing. See warnings afterwards.

Book a technician

Get an electric fence quote

Job card

We WhatsApp or call you back. Fields marked (required) are needed.

Property type
When
Photos (optional, up to 4)

No call-out fee when we do the work. If no work is done, a R650 call-out fee applies.